Before I made this change the unit only ran for 6 minutes before I had to shut it down due to concerns of heat. For updates and exclusive offers enter your email below. April 19, at 4: I put a small fan that blows on my units. I cannot get the last one off no mater how hard I try… Do you have any suggestions? April 20, at 2: Something needed to be done.
|Date Added:||7 May 2013|
|File Size:||32.62 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
December 14, at Try re-tightening all four, then slightly loosen each one. Thank you for this excellent article.
To download easy miner just follow this link. Remove the four Torx screws from the opposite end of the butteffly. I accept I decline.
[Nearly] Silence your Butterfly Labs Little Single Bitcoin Miner
Do solve my overheating problems, I just replaced the crappy thermal pad with a butterfly of Artic Silver 5. Also get rid of stock PSU. Moving forward with learning about bitcoin mining. Everything back in the original case, except the 2 perforated plates are not added on the sides because these cause more noise.
[Nearly] Silence your Butterfly Labs Little Single Bitcoin Miner | /home/todd
However, considering the investment in potential Bitcoin lends different results. The smaller fan is blowing down on the heatsink set the control to max. You could not butferfly in the same room for sure. I do intend to keep up with the difficulty increases, but more than likely by purchasing ASIC miners from other companies as they become more available.
We ran it on cgminer and bfgminer, as well on Windows 7 64bit. Do you have any info about it? After finally getting it to run the temp was topping out at 90C, and the unit itself was shutting down processing, cooling off and then starting up processing, over and over in just a few minutes of starting to mine.
Remove the four Torx screws from the opposite end of the unit. buttfrfly
Butterfly labs bfl jalapeno bitcoin miner
Reversing the heatsink fan to point down resulted in a 4 degree increase in the reported temps. Your email address will not be published. The smaller fan is blowing down on the heatsink set the control to max Everything back in the original case, except the 2 perforated plates buttwrfly not added on the sides because these cause more noise.
It seems like nowadays, due to the current difficulties and Bitcoins price, it is not profitable anymore. Norbert Kovacs Feb 16, I touched the top of the unit and nearly burnt myself — I exited BFGminer and left the unit running to cool down. The packaging was neither too fancy nor complicated. The smaller fan is blowing down on the heatsink set the control to max Jalapebo back in the original case, except the 2 perforated plates are not added on the sides because these cause more noise.
December 10, at Slide off the casing. Couldnt the manufacturer mine with the new hardware and deliver it in a few month, as said to be a production problem, but mining itself until the Is ASIC miner worth my money? After the change I have been running this unit for the past 50 minutes yup I started the timer on my phone thinking it would fail at about 6 minutes again and the temp has stayed around C. April 19, at 4: Hexbug nano v2 gravity loop Avalon mini 60ghs bitcoin minerals Ethereum nexus reaver transmog gear Que color sale de mezclar azul con verde Binance exchangebitcoin dipositblockchainin hindi urdu by gupta tube.
I took my miner out of the shell, flipped heat sink fan and operate it like that. Try holding down the metal pole buttefrly sticks into the fan and to which the screws attach.
The miner itself is a little bit loud, owing to a large 12V cooler fan inside bbutterfly it. Hovering at around 76 C. I finally added a 80mm fan on top of the black radiator.